Angle-Spacer for Canyon Gear Groove Handlebars
€139.90
Available, delivery time: 1-3 days
Product information "Angle-Spacer for Canyon Gear Groove Handlebars"
Angle spacer (1x spacer) for adjusting the angle of the entire extension mount, suitable for Canyon Aeroad Gear Groove handlebars.
Two variants available. Both variants have a 15° angle.
One variant has no change in length or height.
The other variant has 35mm more length (reach) and 20mm more height (stack).
The spacers are a product of Radsport Ibert and not an original part of the manufacturer!
The handlebar and extensions, as well as the bottle cage adapter and bottle cage with bottle, are not included and are only used to illustrate the possible setup. The angle spacer is compatible with the original accessories and is therefore height-adjustable.
The angle spacer is compatible with the original accessories and is therefore height-adjustable.
Scope of delivery: 1x spacer
Angle: 15 degrees
Installation: Mount the spacer on the road bike handlebar using the screws from the Canyon kit (note the screw length!). Install the armrest plate and mount it with the Mono Extension and, if necessary, additional stack spacers (similar to the Canyon original spacer with a 0° angle).
Material: 7075 aluminum, black anodized
Please note: Intensive and frequent indoor training on the turbo trainer often leads to significant sweat loss. Not only steel parts or ball bearings, but also aluminum can corrode if sweat and salt water are not washed off after riding. If the bike is not properly cleaned after riding, this corrosion can occur on both the angle spacers and the original parts of the bike! Appropriate cleaning after training is necessary to ensure the durability of the products!
Login
Suitable adapter for bottle holder mounting:
BTA (between the arms) V2 adapter for mounting a bottle cage, suitable for Canyon Speedmax SLX / CFR with disc brakes. New design with improved durability and the ability to mount a second bottle or push the first bottle further back with an additional adapter (not included in scope of delivery). The adapters are a product from Radsport Ibert and not an original part from the manufacturer! The handlebars and extensions are not part of the product. The BTA adapter is clamped onto the mono extension and screwed to the side. There are 4 M5 threads at the top for mounting a bottle cage in 2 different positions. Attention: Due to the width of 50mm, there must be 50mm of space between the armrest holder and the computer holder, otherwise the BTA adapter cannot be mounted here. The BTA adapter is available in five different angles. The Canyon Mono Extension for the Speedmax has a 5° angle, meaning that without the angle spacer, the bottle is horizontal when the 5° adapter is installed. With a 10° angle spacer, the 15° adapter would be required, and so on. The Canyon Gear Groove Extension has no angle; the angle spacer = BTA angle. Without the angle spacer, I recommend the 5° BTA. Example for Speedmax: Without angle spacer: 5° BTA adapter With 3° Canyon angle spacer: Effective 8°, so 5° BTA adapter is ideal With 6° Canyon angle spacer: Effective 11°, so 10° BTA adapter is ideal With Radsport Ibert angle spacer 10°: Effective 15°, so 15° BTA adapter is ideal With Radsport Ibert angle spacer 15°: Effective 20°, so 20° BTA adapter is ideal With Radsport Ibert angle spacer 20°: Effective 25°, so 25° BTA adapter is ideal Scope of delivery: 1x adapter, 4x screw M5x12mm Angle: 5, 10, 15, 20, 25 degrees (selectable, only one variant included) Material: PA12 SLS black painted Assembly: Slide the holder over the mono extension and tighten the M5 screws hand-tight (max 1 Nm). Tighten the bottle holder with M5 screws to a maximum of 1,5 Nm. Danger! If the torque is too high, the thread inserts can be loosened in 3D printing, so never mount them too tightly.The holder can also be carefully bent open so that it "snaps" around the mono extension - then only a maximum of one side of the pads has to be removed.