Spacer

Angle spacer set (2 pieces with 12 screws) for angling the arm pads on an aero handlebar with elongated screw positioning, such as profile design. Suitable for handlebars with M5 thread and hole spacing max.25mmLeft / right asymmetrical, therefore a widening or narrowing of the arm distance is possible! Angle: 10 ° or 15 ° Material: aluminum 7075 black anodized Thread: 3x M5 Countersink: For M5 screws Distance between the holes: 25mm Distance between the pad holes: 2x 15mm

Angle spacer set (2 pieces with 4 screws) for angling the arm pads on an aerobar with side screw positioning, such as profile design.Angle: 5°, 10° or 15°Material: aluminum 7075 black anodizedThread: M6Countersink: For M6 screwsDistance between the holes: 14 to 22mmDistance between the pad holes: 18mm (e.g. Profile Design Ergo / Race)

Angle spacer set (1x spacer, 2x screws + angle washers) for angling the entire extension bracket, suitable for Specialized Shiv Tri. The spacers are a product of Radsport Ibert and not an original part from the bike company specialized! The handlebars and the extensions are not part of the product, nor are the spacers and studs for changing the height. The angle spacer is compatible with the original accessory parts and can therefore be adjusted in height. Scope of delivery: 1x spacer, 2x screw, 2x angle washer Angle: 5 degrees, 10 degrees, 15 degrees or 20 degrees (selectable, only one variant included) Material: aluminum 7075 black anodized Please note: Intensive and frequent indoor training on the roller trainer often results in a lot of sweat loss. Not only steel parts or ball bearings, aluminum can also corrode if sweat and salt water is not washed off after riding. If the bike is not cleaned appropriately after riding, this corrosion can occur on both the angle spacers and the original parts of the bike! Appropriate cleaning after training is necessary to ensure the durability of the products! Please note: The 5° angle has 42mm reach, more than the other variants. This one is for a more long and stretched position. Due to the design, the cable and drinking tube no longer run in the entire spacer tower but leave it behind the extension holder!

Angle spacer (1x spacer 2x screws) for angling the entire spacer tower, this spacer is a base spacer, suitable for Canyon Speedmax SLX / CFR with disc brakes with 40mm reach.As a base spacer, this spacer is screwed directly onto the basebar; increasing it upwards (more stack) is only possible with 20mm and 4x5mm screws! This spacer allows for a very flat and stretched position. The spacers are a product of Radsport Ibert and not an original part from the manufacturer! The handlebars and the extensions are not part of the product, nor are the spacers for changing the height. The angle spacer is compatible with the original accessory parts and can therefore be adjusted in height. Scope of delivery: 1x spacer, screws Angle: 15 degrees Original angle spacer: You can mount the 3.5 or 7° angle spacer (original accessory) on top of the angle spacer. Reach: Due to the design, the angle spacer increases the reach forwards by 40mm - i.e. the handlebar is mounted further forward than without the angle spacer. Material: aluminum 7075 black anodized Please note: Intensive and frequent indoor training on the roller trainer often results in a lot of sweat loss. Not only steel parts or ball bearings, aluminum can also corrode if sweat and salt water is not washed off after riding. If the bike is not cleaned appropriately after riding, this corrosion can occur on both the angle spacers and the original parts of the bike! Appropriate cleaning after training is necessary to ensure the durability of the products!

Angle spacer (1x spacer) for adjusting the angle of the entire extension mount, suitable for Canyon Aeroad Gear Groove handlebars.  Two variants available. Both variants have a 15° angle. One variant has no change in length or height. The other variant has 35mm more length (reach) and 20mm more height (stack). The spacers are a product of Radsport Ibert and not an original part of the manufacturer! The handlebar and extensions, as well as the bottle cage adapter and bottle cage with bottle, are not included and are only used to illustrate the possible setup. The angle spacer is compatible with the original accessories and is therefore height-adjustable. The angle spacer is compatible with the original accessories and is therefore height-adjustable. Scope of delivery: 1x spacer Angle: 15 degrees Installation: Mount the spacer on the road bike handlebar using the screws from the Canyon kit (note the screw length!). Install the armrest plate and mount it with the Mono Extension and, if necessary, additional stack spacers (similar to the Canyon original spacer with a 0° angle). Material: 7075 aluminum, black anodized Please note: Intensive and frequent indoor training on the turbo trainer often leads to significant sweat loss. Not only steel parts or ball bearings, but also aluminum can corrode if sweat and salt water are not washed off after riding. If the bike is not properly cleaned after riding, this corrosion can occur on both the angle spacers and the original parts of the bike! Appropriate cleaning after training is necessary to ensure the durability of the products!

Angle spacer (1x spacer 2x screws) for angling the entire extension bracket, suitable for Canyon Speedmax SLX / CFR with disc brakes. The spacers are a product of Radsport Ibert and not an original part from the manufacturer! The handlebars and the extensions are not part of the product, nor are the spacers for changing the height. The angle spacer is compatible with the original accessory parts and can therefore be adjusted in height. Scope of delivery: 1x spacer, 2x screw 22mm, 1x 35mm 2x 40mm Angle: 10 degrees, 15 degrees or 20 degrees (selectable, only one variant included) Stock angle spacers: You can add the 3 or 6° angle spacer on top of the angle spacer. Then you need to screw the mono bar with 1x35mm and 1x40mm (for 6°) and with 2x40mm (for 3°) Stack: When using the 20mm base spacer, at least 2x5mm additional spacers, i.e. 30mm in total, must be installed under the angle spacer so that the screws can clamp the spacer without play. For the medium and high base spacers, mounting the angle spacer directly on the base spacer is sufficient. Reach: Due to the design, the angle spacer increases the reach forwards by approx. 20mm - i.e. the handlebar is mounted further forward than without the angle spacer. Assembly: Mount the spacer onto a Canyon base spacer using the screws from the Canyon Fit Kit (note the screw length! Screw a min. 10mm thread length into the Canyon spacer). Mount the mono extension from above using the 22mm screws (pre-assembled) and the ball washers from the Canyon Fit Kit. When using the 3 or 6 degree Canyon angle spacers, use the 35mm or 40mm screws from above. Material: aluminum 7075 black anodized Please note: Intensive and frequent indoor training on the roller trainer often results in a lot of sweat loss. Not only steel parts or ball bearings, aluminum can also corrode if sweat and salt water is not washed off after riding. If the bike is not cleaned appropriately after riding, this corrosion can occur on both the angle spacers and the original parts of the bike! Appropriate cleaning after training is necessary to ensure the durability of the products!

Angle spacer (1x spacer 2x screws) for angling the entire extension bracket, suitable for Canyon Speedmax SLX / CFR with disc brakes. The spacers are a product of Radsport Ibert and not an original part from the manufacturer! The handlebars and the extensions are not part of the product, nor are the spacers for changing the height. The angle spacer is compatible with the original accessory parts and can therefore be adjusted in height. Scope of delivery: 1x spacer, 2x screw 22mm, 1x 35mm 2x 40mm Angle: 15 degrees (selectable, only one variant included) Stock angle spacers: You can add the 3 or 6° angle spacer on top of the angle spacer. Then you need to screw the mono bar with 1x35mm and 1x40mm (for 6°) and with 2x40mm (for 3°) Reach: The angle spacer increases the reach forwards by approx. 50mm - i.e. the handlebar is mounted further forward than without the angle spacer. Stack: When using the 20mm base spacer, at least 2x5mm additional spacers, i.e. 30mm in total, must be installed under the angle spacer so that the screws can clamp the spacer without play. For the medium and high base spacers, mounting the angle spacer directly on the base spacer is sufficient. Assembly: Mount the spacer onto a Canyon base spacer using the screws from the Canyon Fit Kit (note the screw length! Screw a min. 10mm thread length into the Canyon spacer). Mount the mono extension from above using the 22mm screws (pre-assembled) and the ball washers from the Canyon Fit Kit. When using the 3 or 6 degree Canyon angle spacers, use the 35mm or 40mm screws from above. Material: aluminum 7075 black anodized Please note: Intensive and frequent indoor training on the roller trainer often results in a lot of sweat loss. Not only steel parts or ball bearings, aluminum can also corrode if sweat and salt water is not washed off after riding. If the bike is not cleaned appropriately after riding, this corrosion can occur on both the angle spacers and the original parts of the bike! Appropriate cleaning after training is necessary to ensure the durability of the products!

Angle spacer (2x spacer 5x screw set) for replacing the entire extension bracket, suitable for Giant Trinity / Liv Avow. The spacers are a Fourier product and not an original part from the manufacturer! By replacing the extension holder with this holder, the entire extensions including pads are angled by 10° or 15°, which often enables a much more comfortable and aerodynamic position. Scope of delivery: 1x spacer, 5x screw sets for spacer heights of 10, 20, 30, 40, 50 mm Angle: 10 degrees, 15 degrees (selectable, only one variant included) Material: aluminum black anodized

Riser kit to raise an existing BTA bottle cage between the arms. The set contains spacers of 10, 20, 40mm height, these can then be stacked to 10, 20, 30, 40, 50, 60, 70mm height. You can also choose a single riser with a height of 100mm for a very high position. Screws with 110 and 120mm are included here. Bottle holder and BTA holder not included! The holes are 64mm apart and one hole fits M5 screws, which is the standard for bottle holders. Measure beforehand if necessary! Assembly: Use the included M5 screws to raise the bottle holder to the desired height and screw it tight. Material: PETG FDM Scope of delivery: Adapter 1x 10, 20, 40mm each; M5 screws 2x 20, 30, 40, 50, 60, 70, 80mm each; At 100mm: 110 and 120mm

Riser kit to raise an existing BTA bottle cage between the arms. The set contains spacers of 10, 20, 40mm height, these can then be stacked to 10, 20, 30, 40, 50, 60, 70mm height. You can also choose a single riser with a height of 100mm for a very high position. Screws with 110 and 120mm are included here. Bottle holder and BTA holder and Profile Wedge Set not included! The holes are 64mm apart and one hole fits M5 screws, which is the standard for bottle holders. Measure beforehand if necessary! Assembly: Use the included M5 screws to raise the bottle holder to the desired height and screw it tight. Material: PETG FDM Scope of delivery: Adapter 1x 10, 20, 40mm each; M5 screws 2x 20, 30, 40, 50, 60, 70, 80mm each; At 100mm: 110 and 120mm

The HSF BTA Wedges allow you to level your hydration system on any standard BTA mount. The kit includes three 5º wedges, for a total tilt adjustment of 15º - making it easy to align your hydration system to allow maximum filling.  

Profile Design's Aeria Ultimate Race Bracket Kit is an alternative extension clamp and armrest bracket for the Aeria Ultimate time trial handlebar, which is narrower and lighter than the standard version.

Adapter block pair (2 pieces) for mounting on the extension mounting plate of the new Trek Speedconcept for disc brakes. This adapter allows the use of armrests with M5 threads, as the Speedconcept comes with M4 screws. Additionally, the adapter's 10mm stack height allows for more variable armrest positioning compared to the original, smaller armrests. These adapters are a product of Radsport Ibert and not from the bicycle manufacturer! Material: 7075 aluminum, black anodized Scope of delivery: 2x adapter blocks; 4x M4 screws; 4x M5 screws

Adapter block pair (2 pieces) for mounting on the basebar of the new Trek Speedconcept for disc brakes. Thanks to the identical hole spacing, this adapter kit allows the use of Profile Design spacers and accessories, enabling clamps for round 22.2mm extensions. The adapter is placed on the basebar and then raised using Profile Design A2/A3 spacers (A2-A3 adapters required!). For optimal fit, the A3 reach extender is recommended. Ensure correct screw length! M6 screws from the Profile Design spacer kit must be used. Use matching Trek washers for contact with the basebar when screwing from below! These adapters are a product of Radsport Ibert and not from the bicycle manufacturer! Material: 7075 aluminum, black anodized Scope of delivery: 2x adapters for Trek Speedconcept basebar with disc brakes. Profile Design spacers, screws, and other adapters are not included. The setup shown in the picture is for illustrative purposes only, showing the assembled state and intended use.

Angle spacer set (2 pieces with 4 screws) for angling the entire extension bracket on an Avenger aerobar TM6 / K2 (or identical). The shape of the spacers also reduces or increases the arm spacing, which can change the arm position positively.The handlebar and the extensions are not part of the product. Scope of delivery: 1x spacer left, 1x spacer right, 4x screws M5. Angle: 10 or 15 degreesMaterial: aluminum 7075 black anodizedThread: M5Countersink: For M5 screws