Components
AERO Cockpit The Swiss Side AERO COCKPIT is a solution derived from our World Championship winning cockpit projects. Designed in real world conditions and with a human-performance centric approach, this cockpit offers a fully integrated triathlon solution combining all aspects of performance and speed. The AERO Cockpit package includes:1x Extension left1x Extension right2x Extension end plug1x Armrest left1x Armrest right1x Bottle cage holder1x Computer mount arm1x Computer mount slider2x Extension pad (premounted)2x Armrest pad (premounted)1x Computer mount insert set (Garmin + Wahoo)all necessary screws The AERO Cockpit package does not include:BasebarSpacers Bottle cageMore information:https://www.swissside.com/products/aero-cockpit?variant=55156555514243
Aero BTA bottle from Torhans. Aero mount is needed for installation!
Disc Brake Rotor Locking Shield. The Aeroto is an aerodynamic component which has been designed to help improve airflow around disc brake rotors and replaces your existing lock ring on 140mm size centre lock rotors. This one piece stealthy Carbon fibre lens has a bonded durable alloy central fitting and can be easily switched between different rotors (rotor not supplied). Compatible with Shimano, Sram, TRP, A2Z rotors etc and fitted using a regular internal rotor/cassette lock ring tool. Oversized axles which require an external outer locking tool are not compatible. *Note that some TRP brake callipers are not compatible.Note: These are sold as a single item and not a pair. If you need a pair please ensure you order two of the correct size. Note: This is not compatible with the Scott Plasma 6 frame set
Angle spacer set (2 pieces with 12 screws) for angling the arm pads on an aero handlebar with elongated screw positioning, such as profile design. Suitable for handlebars with M5 thread and hole spacing max.25mmLeft / right asymmetrical, therefore a widening or narrowing of the arm distance is possible! Angle: 10 ° or 15 ° Material: aluminum 7075 black anodized Thread: 3x M5 Countersink: For M5 screws Distance between the holes: 25mm Distance between the pad holes: 2x 15mm
Angle spacer set (2 pieces with 4 screws) for angling the arm pads on an aerobar with side screw positioning, such as profile design.Angle: 5°, 10° or 15°Material: aluminum 7075 black anodizedThread: M6Countersink: For M6 screwsDistance between the holes: 14 to 22mmDistance between the pad holes: 18mm (e.g. Profile Design Ergo / Race)
Angle spacer set (1x spacer, 2x screws + angle washers) for angling the entire extension bracket, suitable for Specialized Shiv Tri. The spacers are a product of Radsport Ibert and not an original part from the bike company specialized! The handlebars and the extensions are not part of the product, nor are the spacers and studs for changing the height. The angle spacer is compatible with the original accessory parts and can therefore be adjusted in height. Scope of delivery: 1x spacer, 2x screw, 2x angle washer Angle: 5 degrees, 10 degrees, 15 degrees or 20 degrees (selectable, only one variant included) Material: aluminum 7075 black anodized Please note: Intensive and frequent indoor training on the roller trainer often results in a lot of sweat loss. Not only steel parts or ball bearings, aluminum can also corrode if sweat and salt water is not washed off after riding. If the bike is not cleaned appropriately after riding, this corrosion can occur on both the angle spacers and the original parts of the bike! Appropriate cleaning after training is necessary to ensure the durability of the products! Please note: The 5° angle has 42mm reach, more than the other variants. This one is for a more long and stretched position. Due to the design, the cable and drinking tube no longer run in the entire spacer tower but leave it behind the extension holder!
Angle spacer (1x spacer 2x screws) for angling the entire spacer tower, this spacer is a base spacer, suitable for Canyon Speedmax SLX / CFR with disc brakes with 40mm reach.As a base spacer, this spacer is screwed directly onto the basebar; increasing it upwards (more stack) is only possible with 20mm and 4x5mm screws! This spacer allows for a very flat and stretched position. The spacers are a product of Radsport Ibert and not an original part from the manufacturer! The handlebars and the extensions are not part of the product, nor are the spacers for changing the height. The angle spacer is compatible with the original accessory parts and can therefore be adjusted in height. Scope of delivery: 1x spacer, screws Angle: 15 degrees Original angle spacer: You can mount the 3.5 or 7° angle spacer (original accessory) on top of the angle spacer. Reach: Due to the design, the angle spacer increases the reach forwards by 40mm - i.e. the handlebar is mounted further forward than without the angle spacer. Material: aluminum 7075 black anodized Please note: Intensive and frequent indoor training on the roller trainer often results in a lot of sweat loss. Not only steel parts or ball bearings, aluminum can also corrode if sweat and salt water is not washed off after riding. If the bike is not cleaned appropriately after riding, this corrosion can occur on both the angle spacers and the original parts of the bike! Appropriate cleaning after training is necessary to ensure the durability of the products!
Angle spacer (1x spacer) for adjusting the angle of the entire extension mount, suitable for Canyon Aeroad Gear Groove handlebars. Two variants available. Both variants have a 15° angle. One variant has no change in length or height. The other variant has 35mm more length (reach) and 20mm more height (stack). The spacers are a product of Radsport Ibert and not an original part of the manufacturer! The handlebar and extensions, as well as the bottle cage adapter and bottle cage with bottle, are not included and are only used to illustrate the possible setup. The angle spacer is compatible with the original accessories and is therefore height-adjustable. The angle spacer is compatible with the original accessories and is therefore height-adjustable. Scope of delivery: 1x spacer Angle: 15 degrees Installation: Mount the spacer on the road bike handlebar using the screws from the Canyon kit (note the screw length!). Install the armrest plate and mount it with the Mono Extension and, if necessary, additional stack spacers (similar to the Canyon original spacer with a 0° angle). Material: 7075 aluminum, black anodized Please note: Intensive and frequent indoor training on the turbo trainer often leads to significant sweat loss. Not only steel parts or ball bearings, but also aluminum can corrode if sweat and salt water are not washed off after riding. If the bike is not properly cleaned after riding, this corrosion can occur on both the angle spacers and the original parts of the bike! Appropriate cleaning after training is necessary to ensure the durability of the products!
Angle spacer (1x spacer 2x screws) for angling the entire extension bracket, suitable for Canyon Speedmax SLX / CFR with disc brakes. The spacers are a product of Radsport Ibert and not an original part from the manufacturer! The handlebars and the extensions are not part of the product, nor are the spacers for changing the height. The angle spacer is compatible with the original accessory parts and can therefore be adjusted in height. Scope of delivery: 1x spacer, 2x screw 22mm, 1x 35mm 2x 40mm Angle: 10 degrees, 15 degrees or 20 degrees (selectable, only one variant included) Stock angle spacers: You can add the 3 or 6° angle spacer on top of the angle spacer. Then you need to screw the mono bar with 1x35mm and 1x40mm (for 6°) and with 2x40mm (for 3°) Stack: When using the 20mm base spacer, at least 2x5mm additional spacers, i.e. 30mm in total, must be installed under the angle spacer so that the screws can clamp the spacer without play. For the medium and high base spacers, mounting the angle spacer directly on the base spacer is sufficient. Reach: Due to the design, the angle spacer increases the reach forwards by approx. 20mm - i.e. the handlebar is mounted further forward than without the angle spacer. Assembly: Mount the spacer onto a Canyon base spacer using the screws from the Canyon Fit Kit (note the screw length! Screw a min. 10mm thread length into the Canyon spacer). Mount the mono extension from above using the 22mm screws (pre-assembled) and the ball washers from the Canyon Fit Kit. When using the 3 or 6 degree Canyon angle spacers, use the 35mm or 40mm screws from above. Material: aluminum 7075 black anodized Please note: Intensive and frequent indoor training on the roller trainer often results in a lot of sweat loss. Not only steel parts or ball bearings, aluminum can also corrode if sweat and salt water is not washed off after riding. If the bike is not cleaned appropriately after riding, this corrosion can occur on both the angle spacers and the original parts of the bike! Appropriate cleaning after training is necessary to ensure the durability of the products!
Angle spacer (1x spacer 2x screws) for angling the entire extension bracket, suitable for Canyon Speedmax SLX / CFR with disc brakes. The spacers are a product of Radsport Ibert and not an original part from the manufacturer! The handlebars and the extensions are not part of the product, nor are the spacers for changing the height. The angle spacer is compatible with the original accessory parts and can therefore be adjusted in height. Scope of delivery: 1x spacer, 2x screw 22mm, 1x 35mm 2x 40mm Angle: 15 degrees (selectable, only one variant included) Stock angle spacers: You can add the 3 or 6° angle spacer on top of the angle spacer. Then you need to screw the mono bar with 1x35mm and 1x40mm (for 6°) and with 2x40mm (for 3°) Reach: The angle spacer increases the reach forwards by approx. 50mm - i.e. the handlebar is mounted further forward than without the angle spacer. Stack: When using the 20mm base spacer, at least 2x5mm additional spacers, i.e. 30mm in total, must be installed under the angle spacer so that the screws can clamp the spacer without play. For the medium and high base spacers, mounting the angle spacer directly on the base spacer is sufficient. Assembly: Mount the spacer onto a Canyon base spacer using the screws from the Canyon Fit Kit (note the screw length! Screw a min. 10mm thread length into the Canyon spacer). Mount the mono extension from above using the 22mm screws (pre-assembled) and the ball washers from the Canyon Fit Kit. When using the 3 or 6 degree Canyon angle spacers, use the 35mm or 40mm screws from above. Material: aluminum 7075 black anodized Please note: Intensive and frequent indoor training on the roller trainer often results in a lot of sweat loss. Not only steel parts or ball bearings, aluminum can also corrode if sweat and salt water is not washed off after riding. If the bike is not cleaned appropriately after riding, this corrosion can occur on both the angle spacers and the original parts of the bike! Appropriate cleaning after training is necessary to ensure the durability of the products!
Angle spacer (2x spacer 5x screw set) for replacing the entire extension bracket, suitable for Giant Trinity / Liv Avow. The spacers are a Fourier product and not an original part from the manufacturer! By replacing the extension holder with this holder, the entire extensions including pads are angled by 10° or 15°, which often enables a much more comfortable and aerodynamic position. Scope of delivery: 1x spacer, 5x screw sets for spacer heights of 10, 20, 30, 40, 50 mm Angle: 10 degrees, 15 degrees (selectable, only one variant included) Material: aluminum black anodized
Adapter for extending the BTA Adapter V2. Attention: The rail is NOT compatible with the BTA Adapter V1, which is only designed and approved for one bottle! This adapter allows you to position the water bottle further back toward your upper body or to mount a second bottle. Installation: The adapter rail is screwed directly onto the BTA V2 adapter using the included 4x M5x12mm countersunk screws. Raising the rail with a riser kit is not permitted! If a bottle cage is mounted directly onto the rail, 1-2 countersunk screws must be removed accordingly. The bottle cage is then mounted using the included M5x16 fillister head screws, with the screw then passing "through" the rail. At least 2 of the countersunk screws must remain installed under the bottle cage, ensuring that the rail is always secured to the BTA adapter with at least 4 screws. (See images) Material: Black anodized 7075 aluminum (image shows the silver version before anodizing!) Countersunk: For M5 screws Scope of delivery: Adapter rail and all screws required for installation. The BTA adapter itself is not included!
Riser kit to raise an existing BTA bottle cage between the arms. The set contains spacers of 10, 20, 40mm height, these can then be stacked to 10, 20, 30, 40, 50, 60, 70mm height. You can also choose a single riser with a height of 100mm for a very high position. Screws with 110 and 120mm are included here. Bottle holder and BTA holder not included! The holes are 64mm apart and one hole fits M5 screws, which is the standard for bottle holders. Measure beforehand if necessary! Assembly: Use the included M5 screws to raise the bottle holder to the desired height and screw it tight. Material: PETG FDM Scope of delivery: Adapter 1x 10, 20, 40mm each; M5 screws 2x 20, 30, 40, 50, 60, 70, 80mm each; At 100mm: 110 and 120mm
Riser kit to raise an existing BTA bottle cage between the arms. The set contains spacers of 10, 20, 40mm height, these can then be stacked to 10, 20, 30, 40, 50, 60, 70mm height. You can also choose a single riser with a height of 100mm for a very high position. Screws with 110 and 120mm are included here. Bottle holder and BTA holder and Profile Wedge Set not included! The holes are 64mm apart and one hole fits M5 screws, which is the standard for bottle holders. Measure beforehand if necessary! Assembly: Use the included M5 screws to raise the bottle holder to the desired height and screw it tight. Material: PETG FDM Scope of delivery: Adapter 1x 10, 20, 40mm each; M5 screws 2x 20, 30, 40, 50, 60, 70, 80mm each; At 100mm: 110 and 120mm
BTA (between the arms) V2 adapter for mounting a bottle cage, suitable for Canyon Speedmax SLX / CFR with disc brakes. New design with improved durability and the ability to mount a second bottle or push the first bottle further back with an additional adapter (not included in scope of delivery). The adapters are a product from Radsport Ibert and not an original part from the manufacturer! The handlebars and extensions are not part of the product. The BTA adapter is clamped onto the mono extension and screwed to the side. There are 4 M5 threads at the top for mounting a bottle cage in 2 different positions. Attention: Due to the width of 50mm, there must be 50mm of space between the armrest holder and the computer holder, otherwise the BTA adapter cannot be mounted here. The BTA adapter is available in five different angles. The Canyon Mono Extension for the Speedmax has a 5° angle, meaning that without the angle spacer, the bottle is horizontal when the 5° adapter is installed. With a 10° angle spacer, the 15° adapter would be required, and so on. The Canyon Gear Groove Extension has no angle; the angle spacer = BTA angle. Without the angle spacer, I recommend the 5° BTA. Example for Speedmax: Without angle spacer: 5° BTA adapter With 3° Canyon angle spacer: Effective 8°, so 5° BTA adapter is ideal With 6° Canyon angle spacer: Effective 11°, so 10° BTA adapter is ideal With Radsport Ibert angle spacer 10°: Effective 15°, so 15° BTA adapter is ideal With Radsport Ibert angle spacer 15°: Effective 20°, so 20° BTA adapter is ideal With Radsport Ibert angle spacer 20°: Effective 25°, so 25° BTA adapter is ideal Scope of delivery: 1x adapter, 4x screw M5x12mm Angle: 5, 10, 15, 20, 25 degrees (selectable, only one variant included) Material: PA12 SLS black painted Assembly: Slide the holder over the mono extension and tighten the M5 screws hand-tight (max 1 Nm). Tighten the bottle holder with M5 screws to a maximum of 1,5 Nm. Danger! If the torque is too high, the thread inserts can be loosened in 3D printing, so never mount them too tightly.The holder can also be carefully bent open so that it "snaps" around the mono extension - then only a maximum of one side of the pads has to be removed.
Adapter for extending the computer mount on the time trial bike. The adapter is screwed onto the existing computer holder and the computer holder is then screwed onto the adapter. This extends the position of the computer by 52mm forward and 5mm upwards for better visibility of the computer on the bike! For further extension, 2 adapters can also be screwed "in a row" to bring the computer further 52mm to the front. However, a large computer should no longer be used here, otherwise the leverage on the threads can become too great, depending on the road surface and driving style. Scope of delivery: 1x adapter 90mm; 2x screw M3 The adapter is a product from Radsport Ibert, the image shows the adapter mounted on an existing computer holder and is for illustrative purposes only. Made in Germany! Material: aluminum 7075 black anodized Thread: 2x M3 (M3 screws included) Countersink: For M3 screws
The double BTS bracket is designed to let riders easily run a stacked bottle setup behind their V8 TT+Tri saddle! This bracket provides offset to make sure riders have plenty of room on the saddle, and even integrates two of our bottle retention loops to prevent losing any hydration or nutrition
Aero water bottle by Elite with screw top, no more leakage! The bottle that matches the Aero Tool Box. It's 2025 design in smooth, just the bottle without the holder! Compatible with the 2021 and 2023 bottle cages. The old cages can be upgraded with the new bottle.
Elite aero bottle with fiberglas holder/cage.The bottle that matches the Aero Tool Box. NEW with mouthpiece to open and close, no more leaks! Only the 2023 model "without dimples" with the lines available!
Aero water bottle from Elite with fiberglas cage. New 2025 model with screw cap! The bottle that fits the Aero Tool Box. Compatible with the 2021 and 2023 bottle cages. The old cages can be upgraded with the new bottle.
Elite aero bottle with carbon holder/cage. The bottle that matches the Aero Tool Box. NEW with mouthpiece to open and close, no more leaks! Only the 2023 model "without dimples" with the lines available!
Aero water bottle from Elite with carbon cage. New 2025 model with screw cap! The bottle that fits the Aero Tool Box.Compatible with the 2021 and 2023 bottle cages. The old cages can be upgraded with the new bottle.
Clik extension nozzles for Fumpa pumps. Developed in partnership with the Clik team this new kit contains a genuine Clik connector, a Fumpa right-angle adaptor, two 360-degree rotating joints and 1m of air hose which can be cut to the length you require. With this kit you will get the full Clik Valve experience - perfect airtight connection, audible 'click' on connect and easy disconnect. This extension nozzle mounts on your favourite Fumpa pump: Nano, Mini, Mini+, Fumpa Classic, Fumpa OG or Fumpablack.