Adapter for extending the BTA Adapter V2.
Attention: The rail is NOT compatible with the BTA Adapter V1, which is only designed and approved for one bottle!
This adapter allows you to position the water bottle further back toward your upper body or to mount a second bottle. Material: Black anodized 7075 aluminum (image shows the silver version before anodizing!) Countersunk: For M5 screws Scope of delivery: Adapter rail and all screws required for installation. The BTA adapter itself is not included!
SALE Var. 1 - neu Var. 2 available!BTA (between the arms) adapter for mounting a bottle cage, suitable for Canyon Speedmax SLX / CFR with disc brakes.
The adapters are a product from Radsport Ibert and not an original part from the manufacturer!
The handlebars and extensions are not part of the product. The BTA adapter is clamped onto the mono extension and screwed to the side. There are 4 M5 threads at the top for mounting a bottle cage in 2 different positions.
Attention: Due to the width of 50mm, there must be 50mm of space between the armrest holder and the computer holder, otherwise the BTA adapter cannot be mounted here.The adapter is designed for mounting a drinking bottle and holder, not for mounting a second bottle underneath (with additional adapters) - this can lead to breakage!
The BTA adapter is available in 5 different angles. The Canyon Mono Extension has an angle of 5° itself, i.e. without an angled spacer the bottle is horizontal when the 5° adapter is mounted. With an angle spacer of 10°, the 15° adapter would be required, etc.
Scope of delivery: 1x adapter, 4x screw M4x12mm Angle: 5, 10, 15, 20, 25 degrees (selectable, only one variant included)
Material: PA12 SLS black painted
Assembly: Slide the holder over the mono extension and tighten the M4 screws hand-tight (max 1 Nm). Tighten the bottle holder with M5 screws to a maximum of 1,5 Nm. Danger! If the torque is too high, the thread inserts can be loosened in 3D printing, so never mount them too tightly.The holder can also be carefully bent open so that it "snaps" around the mono extension - then only a maximum of one side of the pads has to be removed. The adapter is NOT designed to mount additional bottles using other adapters. The adapter is designed exclusively for mounting a bottle holder and a bottle. Mounting multiple filled bottles can cause breakage.
BTA (between the arms) V2 adapter for mounting a bottle cage, suitable for Canyon Speedmax SLX / CFR with disc brakes.
New design with improved durability and the ability to mount a second bottle or push the first bottle further back with an additional adapter (not included in scope of delivery).
The adapters are a product from Radsport Ibert and not an original part from the manufacturer!
The handlebars and extensions are not part of the product. The BTA adapter is clamped onto the mono extension and screwed to the side. There are 4 M5 threads at the top for mounting a bottle cage in 2 different positions.
Attention: Due to the width of 50mm, there must be 50mm of space between the armrest holder and the computer holder, otherwise the BTA adapter cannot be mounted here.The adapter is designed for mounting a drinking bottle and holder, not for mounting a second bottle underneath (with additional adapters) - this can lead to breakage!
The BTA adapter is available in 5 different angles. The Canyon Mono Extension has an angle of 5° itself, i.e. without an angled spacer the bottle is horizontal when the 5° adapter is mounted. With an angle spacer of 10°, the 15° adapter would be required, etc.
Scope of delivery: 1x adapter, 4x screw M5x12mm Angle: 5, 10, 15, 20, 25 degrees (selectable, only one variant included)
Material: PA12 SLS black painted
Assembly: Slide the holder over the mono extension and tighten the M5 screws hand-tight (max 1 Nm). Tighten the bottle holder with M5 screws to a maximum of 1,5 Nm. Danger! If the torque is too high, the thread inserts can be loosened in 3D printing, so never mount them too tightly.The holder can also be carefully bent open so that it "snaps" around the mono extension - then only a maximum of one side of the pads has to be removed.
Adapter for extending the computer mount on the time trial bike. The adapter is screwed onto the existing computer holder and the computer holder is then screwed onto the adapter. This extends the position of the computer by 52mm forward and 5mm upwards for better visibility of the computer on the bike! For further extension, 2 adapters can also be screwed "in a row" to bring the computer further 52mm to the front. However, a large computer should no longer be used here, otherwise the leverage on the threads can become too great, depending on the road surface and driving style. Scope of delivery: 1x adapter 90mm; 2x screw M3
The adapter is a product from Radsport Ibert, the image shows the adapter mounted on an existing computer holder and is for illustrative purposes only. Made in Germany!
Material: aluminum 7075 black anodized
Thread: 2x M3 (M3 screws included) Countersink:
For M3 screws
No-turn insert for the 76 projects computer mount. This allows the computer to be mounted without turning, for very narrow or hard-to-reach computer positions.
Profile Design Riser Kit - Adapters | A2 to A3 | Aluminum
Four-piece set with aluminum adapters for using current A3 risers on older A2 systems. The adapters create an additional stack of 25 mm.
Compatible with the Aeria Ultimate aerobar from Profile Design. When
using base bars from other manufacturers, the 25 mm is the minimum stack. In this case, the corresponding bolt length specifications must also be observed.
Scope of supply:
4 adapters: 2x top (15 mm), 2x bottom (10 mm, left + right)
Installation: For installation, please follow the instructions and manual on www.profile-design-eu.com!
Profile Design A2A Hi-Riser Kit (5/10/20mm*6) The A2A risers are specially designed for the Aeria Ultimate. The system is also compatible with A2/A3 adapters. SPECIFICATIONS Maximum height: 80mm Specially designed for the Aeria Ultimate Includes an aluminum bridge Compatible with the A2 riser system Can be used with an adapter with the A3 riser system Color: Black Weight: (Complete kit) 35mm: 570g 60mm: 770g Contents: Profile Design A2A Hi-Riser Kit (5/10/20mm*6) Risers: 2x 5mm | 2x 10 mm | 6x 20mm 1x Bridge (5mm)
Installation: For installation, please follow the instructions and manual on www.profile-design-eu.com!
Profile Design A2A Low-Riser Kit (5/10/20mm)
The A2A risers are specifically designed for the Aeria Ultimate. The system is also compatible with A2/A3 adapters. SPECIFICATIONS
Maximum height: 35mm Specifically designed for the Aeria Ultimate Compatible with the A2 riser system
Can be used with an adapter for the A3 riser system Color: Black Weight: (Complete kit) 35mm: 570g 60mm: 770g Scope of delivery:1x Profile Design A2A Low-Riser Kit (5/10/20mm) Riser: 2x 5mm | 2x 10 mm | 2x 20mm
Installation: For installation, please follow the instructions and manual on www.profile-design-eu.com!
Profile Design Riser Kit - Adapters | A3 | Reach Extender for Armrests
The two aluminum adapters for triathlon handlebars, which are equipped with A3 riser systems, allow the reach
of the armrests to be increased by 32 mm. By using the corresponding
adapter set (not included), also a combination with A2 systems is
possible.
The adapter kit makes it easier for the rider to adopt a longer aero
position. From the original construction of the aerobar retains the
front bolt that connects handlebar and base (bracket) to ensure a secure and firm structure.
Technical details of the Profile Design A3 reach extender
riser height: 25 mm
offset: 30 mm
weight: approx. 90 g (manufacturer's specification)
Compatibility:
handlebars / aerobars: Wing 20c+, Wing Ultimate, Aeria Ultimate (with "A2 to A3" adapters)
bikes: BMC Speedmachine, Canyon Speedmax CF (2024), Wilier Supersonica
Scope of supply:
2 adapters (left + right) incl. 2 bolts (M6 x 35 mm) and 2 washers (6 x 12 x 1.5 mm)
Installation:
For installation, please follow the instructions and manual on www.profile-design-eu.com!
Profile Design Riser Kit - A3A | High | Aluminum | for Wing 20c+/Ultimate
The A3 risers are designed specifically for the Wing
20C+ and Wing Ultimate. The system is backwards compatible with A2
risers by using the A2/A3 adapter.
Key Features of the Profile Design Aerobar A3A Hi-Riser Kit
Compatibility: Wing 20C+ and Wing Ultimate
Compatible with the A3 riser system
Can be used with A2 riser system with adaptor
Maximum Height: A3A High Riser w/A2 Bridge Kit = 60mm
A3A High Riser w/A2 Bridge Kit Includes:
Risers:
5mm: 2 Risers10mm: 2 Risers40mm: 2 Risers
Bolts:
80mm: 4 Bolts85mm: 4 Bolts90mm: 4 Bolts95mm: 4 Bolts100mm: 4 Bolts
Accessories:
4x Washers, 1x A2 Bridge (5mm)
Installation: For installation, please follow the instructions and manual on www.profile-design-eu.com!
Profile Design Riser Kit - A3A | Low | Aluminum | for Wing 20c+/Ultimate
The A3 risers are designed specifically for the Wing
20C+ and Wing Ultimate. The system is backwards compatible with A2
risers by using the A2/A3 adapter.
Key Features of the Profile Design Aerobar A3A Low-Riser Kit
Compatibility: Wing 20C+ and Wing Ultimate
Compatible with the A3 riser system
Can be used with A2 riser system with adaptor
Maximum Height: A3A Low Riser Kit = 35mm
A3A Low Riser Kit Includes:
Risers:
5mm: 2 Risers10mm: 2 Risers20mm: 2 Risers
Bolts:
45mm: 4 Bolts50mm: 4 Bolts55mm: 4 Bolts60mm: 4 Bolts65mm: 4 Bolts70mm: 4 Bolts75mm: 4 Bolts
Accessories:
Washer: 4 Washers
Installation: For installation, please follow the instructions and manual on www.profile-design-eu.com!
Bottle holder for mounting behind the saddle. Suitable for frames that have an attachment to a round rail at the top of the seat post, such as Cube Aerium or Avenger TM6. The adapter is inserted into the seat post instead of the tube with the threads and mounted from above with the screws for the saddle clamp.
Profile Design Tilt Booster
Four-piece set with aluminum adapters for using current A3 risers on older A2 systems. The adapters create an additional stack of 25 mm.
Compatible with the Aeria Ultimate aerobar from Profile Design. When
using base bars from other manufacturers, the 25 mm is the minimum stack. In this case, the corresponding bolt length specifications must also be observed.
Scope of supply:
4 adapters: 2x top (15 mm), 2x bottom (10 mm, left + right)
Installation: For installation, please follow the instructions and manual on www.profile-design-eu.com!
Computer holder from 76 projects from UK. Thanks to the modular design, it can be customized for different cockpit variants, extension forms and hand or arm positions.